Gorman-Rupp PA10A60 Prime Aire Pump
Spare Parts for the Gorman-Rupp PA10A60 Priming-assisted dewatering pump
Product Summary
Genuine OEM spare parts for the Gorman-Rupp PA10A60, a priming-assisted pump that primes and re-primes automatically using a vacuum-assisted priming system, usually supplied as an engine-driven set. Impellers, seals, wear parts, check valves and bearings, plus priming-system parts, are listed below with Gorman-Rupp part numbers from manual OM-07157-01.
Spare Parts List
✓ Tick the parts you need. Codes are as printed in the Gorman-Rupp parts list; build variants and older serial numbers can use different parts, so pick your model in the form below. Not sure? Add a photo of the nameplate (model and serial number) and we’ll match the parts for you.
| Select | Part (as printed by Gorman-Rupp) | Part number & reference |
|---|---|---|
| Wear & Service Parts | ||
| Impeller | Part no. 38615-091 11010 · Item 2 | |
| 1.88 Dia. Seal Assy | Part no. 46512-048 · Item 3 | |
| Wear Ring | Part no. 38691-634 11010 · Item 35 | |
| Check Valve Kit 10" | Part no. 48274-007 · Item 3 | |
| Check Valve | Part no. 26642-148 | |
| Flapper | Part no. 26688-007 | |
| Cover Gasket | Part no. 26688-008 | |
| Seals, Bearings & Shaft | ||
| O-Ring | Part no. 25152-463 | |
| Gasket | Part no. 25113-040 | |
| Gasket | Part no. 25113-034 · Item 10 | |
| Seal Plate | Part no. 38272-716 10000 · Item 6 | |
| O-Ring | Part no. 25152-276 · Item 7 · Qty 2 | |
| Ball Bearing | Part no. 23422-413 · Item 18 | |
| Impeller Shaft | Part no. 38512-524 1706H · Item 20 | |
| Oil Seal | Part no. 25258-725 · Item 22 | |
| Gasket | Part no. 38683-475 18000 · Item 24 | |
| Ball Bearing | Part no. S1911 · Item 28 | |
| Gasket | Part no. 3200G 18000 · Item 29 | |
| O-Ring | Part no. 25152-277 · Item 31 | |
| Gasket | Part no. 38687-053 19060 · Item 8 | |
| Priming Valve Gasket | Part no. 38683-657 19060 · Item 4 | |
| Priming System | ||
| Priming Chamber Kit | Part no. 48275-005 · Item 2 | |
| Priming Chamber Assy | Part no. 46112-709 · Item 1 | |
| Priming Valve | Part no. 26664-007 · Item 1 | |
| Orifice Button | Part no. 26688-021 | |
| Priming Chamber | Part no. 38343-020 10000 · Item 5 | |
| Strainer Assy | Part no. 46641-222 17000 · Item 6 | |
| Other Core Parts | ||
| 10" Strainer | Part no. 46641-011 24150 | |
| Bearing Cover | Part no. 38322-432 10000 · Item 17 | |
| Seal Cavity Sight Gauge | Part no. S1471 · Item 25 | |
| Coupling | Part no. 24391-102 · Item 1 | |
How we confirm the exact part: Part numbers on this page are as printed in Gorman-Rupp manual OM-07157-01, parts list for serial numbers 1670834 and up. Pumps with earlier serial numbers, an “N” serial suffix or a different build can use different parts, so send the serial number or a nameplate photo and we’ll confirm the right part before we quote. Engine and power-unit parts are not covered on this page.
Service Intervals & When to Replace
- Daily: check general condition (temperature, noise, vibration, leaks) and pump performance (gauges, speed, flow).
- Lubrication: check bearing and seal-cavity lubrication weekly; replace the oil annually (Gorman-Rupp specifies SAE No. 30 non-detergent oil where oil is used).
- Every six months: inspect front impeller clearance (wear plate) and rear clearance (seal plate) and adjust or replace worn parts.
- Annually: inspect the check valve, bearings, shaft deflection and pump-to-driver alignment; clean the pressure relief valve.
- New applications: inspect wearing parts after the first 250 hours to set your wear rate. Intervals assume about 4,000 hours a year of intermittent duty; shorten them for abrasive or continuous duty.
Models
One page covers the PA10A60 pump end across its engine and drive builds. The pump end, priming chamber and check valve parts are common; engine parts are not listed. The full model code is on the pump nameplate.
Models & Key Specifications
| Model | Series | Ports (suction x discharge) | Max solids | Seal (as listed) | Parts list |
|---|---|---|---|---|---|
| PA10A60 | Prime Aire (PA Series) | 10" (250 mm) | 3.25" (83 mm) | 1.88 Dia. Seal Assy | OM-07157-01 (S/N 1670834+) |
Port size and solids handling from Gorman-Rupp model data; parts from manual OM-07157-01. Typical uses: site and mine dewatering, bypass pumping and hire fleets.
Troubleshooting
Pump fails to prime
Likely cause: Discharge check valve contaminated, damaged or not seating, an air leak in the suction line, a worn seal or gasket, a damaged air compressor or broken belt, or a clogged strainer. Action: Clean or replace the check valve, correct leaks, check pump vacuum and replace the worn seal or gasket, repair the compressor or belts, and clean the strainer.
Low flow or pressure
Likely cause: Eductor or strainer clogged, impeller or other wearing parts worn or damaged, or suction lift too high. Action: Clean the eductor and strainer, replace worn parts and check the impeller is centred and turns freely, and reduce suction lift.
Pump clogs frequently
Likely cause: Discharge flow too slow, a clogged or binding check valve, or liquid too thick. Action: Open the discharge valve fully, run at full governed speed, clean the check valve and dilute if possible.
Pump requires too much power
Likely cause: Pump speed too high, discharge head too low, liquid too thick, or a frozen pump or jack shaft bearing. Action: Check driver output, adjust the discharge valve, dilute if possible, and check and replace bearings.
Request for Quotation
Selected Parts:
- No parts selected
Not sure which parts? Just send a photo of the nameplate or part below.
Gorman-Rupp PA10A60 spare parts: frequently asked questions
Tap a question to see the answer.
What spare parts are listed for the Gorman-Rupp PA10A60?
Parts come from Gorman-Rupp manual OM-07157-01, grouped as wear and service parts; seals, bearings and shaft; priming system; and other core parts. They include the impeller, seal assembly, wear ring, check valve kit, check valve and flapper, each listed with its Gorman-Rupp part number as printed.
Why won’t my PA10A60 prime?
Likely causes from the troubleshooting guide: discharge check valve contaminated, damaged or not seating, an air leak in the suction line, a worn seal or gasket, a damaged air compressor or broken belt, or a clogged strainer. The fixes are in the troubleshooting table above.
How do I restore lost flow or pressure on a PA10A60?
The troubleshooting guide on this page lists the likely causes as: eductor or strainer clogged, impeller or other wearing parts worn or damaged, or suction lift too high. Clean the eductor and strainer, replace worn parts and check the impeller is centred and turns freely, and reduce suction lift.
How do I make sure I order the right PA10A60 parts?
Tick the parts you need and your selection carries into the quote form. Add a nameplate photo or serial number and we’ll confirm the parts before quoting. See other models in our Prime Aire Series parts, or all Gorman-Rupp spare parts.